Artwork Guidelines and Helpful Tips
You worked hard designing the perfect label, the last thing you want is to pick up the finished product only to see a blurry image or pixelated graphic. Help is here! Follow the instructions and helpful hints below for high-resolution, high-quality printed labels.
At A Glance
- Resolution is at least 300 dpi
- Bleed extends at least 1/8" past label outline
- Safe margin is observed
- Color palette is CMYK*
- File type is .ai, .eps, .png, .jpg, .jpeg, .gif, or .pdf
- File size is no larger than 40 MB
- Fonts are at least 6 point size and easy to read
- Borders are at least 0.5 points
- Graphics are embedded (not linked)
- Label outlines have been removed
- Material color is a part of your design considerations
- Proofing has been completed
Blurry or pixelted images can happen when you overly enlarge a file or if you start with a low-quality image from the internet. While your photos and graphics may appear fine on-screen, the final printed product likely will not. This is because web-based images typically range from 72-96 dpi whereas print images require 300 dpi or greater for clarity.
To check the resolution of your existing image, complete the following steps:
- Save the file to your computer
- Right-click on the icon and select "Properties"
- Switch to the "Details" tab
- Look to the lines for "Horizontal/Vertical resolution"
Here are a few suggestions for fixing low resolution imagery:
- Reupload your image to see if it was compressed during the process
- Find a higher resolution version online (stock photo libraries are a great resource)
- Use photo editing software
- Reduce the size of the graphic on your label
If all else fails, you may want to consider removing the low-resolution element.
"Bleed" is when you allow your design to transcend the dimensions of the label. It ensures that your design reaches the edge of the label once it's peeled up from the liner. This is important because it accounts for any shifting that may occur throughout the printing process.
Here are a few suggestions for adding bleed in any design program:
- Stretch your design beyond the label dieline (outline)
- Add a thick border
- Set a background color across the entire sheet
3. Safe Margin
Also called the safe zone, this is the area within 0.125" of the label dieline (outline). It's there to ensure no valuable part of your design ends gets cut off. This is important beacuse it accounts for any shifting that may occur throughout the printing process.
To observe the safe zone, pull your design inward toward the center of the label. This includes keeping text, design elements, and more away from the edge. We recommend at least 1/8" or 1/16" of space between your design and the outline of your label.
4. Color Palette
Consider how the colors in your design might look once they're printed. Because colors on-screen display in RGB and printers use CMYK colors, you may notice a loss of vibrancy or slight shifts in color.
This can be especially noticeable with the color black, the printed version can appear more gray. To ensure the blacks in your file print dark enough, use rich black. The CMYK values for rich black are: C=75, M=68, Y=67, K=90. To create a rich black in Maestro Label Designer, use the HEX code 000000.
5. File Type
To build or layout your design in Maestro Label Designer, you can upload the following file types: .jpg, .jpeg, .gif. .png, or .pdf. For uploading your completed design to the custom printed label tool, your file should be one of the follwing: .ai, .eps, .png, .jpg, .jpeg, .gif, or .pdf.
6. File Size
Maestro Label Designer can accept uploads up to 3 MB in size during the design process. If you're uploading a completed design to custom printed label tool, your file should not exceed 40 MB.
Effective labels should be easy to read. Use caution when choosing your font choice, text size, and type color – they can have a large impact on the end result.
Here are a few tips for effortlessly legible labels:
- Use large font sizes (no smaller than 6 pt)
- Be careful with extremely thin fonts
- Avoid overly curly or decorative typefaces
- Switch to high-contrast color combinations
- Reduce the amount of text (paragraphs of text can feel overwhelming and blend together)
It's also important to remember the actual size of your label. Designs can look much bigger on screen than their printed counterparts. You may want to print your design on regular paper to test it out. Hold the sheet at arm's length and see if you can read your labels.
With thin borders, any shifting during printing can be highly noticeable. We recommend a minimum of 0.5 for the line/stroke width, though the thicker the better. Bold borders mask any printer shifts and help maintain the integrity of your design.
If you're working in a design program, it's important to check the location of your photos and graphics. If graphics are linked, we won't be able to access your full label design. For best results, flatten your layers into a single background layer. This includes converting/preserving fonts (learn more).
Caution: Flattening your files means you can no longer make changes to individual layers. Be sure not to save over the original version when flattening.
10. Label Outlines
If you used a label template to create your design, make sure to go back in and delete it before printing or uploading your artwork. Should any shifting occur, the label outlines will be a dead giveaway and take away from your design. Dielines are not the only things you may want to remove. Check that crop marks, registration marks, and the color scale are also removed from your final file.
11. Material Color
If you're using clear labels, consider how the background might affect the visibility of your design and the accuracy of your color palette. The transparency can play a huge factor in how your final product comes out.
Similar rules apply for our collection of color labels. If you're using a brown kraft or gold label, shown above, the material will show through some of the colors in your design.
Always check the spelling, layout, and colors in your document before hitting print or submit.
Our image quality guide is designed to take the guesswork out of designing and printing your labels. For more questions related to image uploads in Maestro Label Designer or the custom printed label tool, reach out to our customer service team at 1-888-575-2235 or submit a support ticket. Be sure to share your labels in our Customer Ideas gallery when you're done and share any of your helpful tricks in our forums.